Version 0.75

chipdef.h

@@ -72,7 +72,8 @@
   #define sig_byte2 0x93
   #define sig_byte1 0x07
   
-  #define devtype 0x77       // Mega8 boot device code
+  //#define devtype 0x77       // Mega8 boot device code
+  #define devtype 0x76       // Mega8 boot device code
   
 //  #define PAGESIZE 64        // Size in Bytes
   

main.c

@@ -1,7 +1,7 @@
 /*****************************************************************************
 *
 * AVRPROG compatible boot-loader
-* Version  : 0.7 (Feb. 2005)
+* Version  : 0.75 (Feb. 2006)
 * Compiler : avr-gcc 3.4.1 / avr-libc 1.0.2 
 * size     : depends on features and startup ( minmal features < 512 words)
 * by       : Martin Thomas, Kaiserslautern, Germany
@@ -12,7 +12,12 @@
 *            owners in source-code and documentation of derived 
 *            work. No warranty.
 *
-* Tested with ATmega8, ATmega16, ATmega32, ATmega128
+* Additional code and improvements contributed by:
+* - Uwe Bonnes
+* - Bjoern Riemer
+*
+*
+* Tested with ATmega8, ATmega16, ATmega32, ATmega128, AT90CAN128
 *
 * - based on the Butterfly Bootloader-Code
 *   Copyright (C) 1996-1998 Atmel Corporation
@@ -133,8 +138,8 @@ int main(void)
     
 	cli();
 	
-	MCUCR = (1<<IVCE);       
+	MCUCR = (1<<IVCE);   // move interruptvectors to the Boot sector    
-	MCUCR = (1<<IVSEL);             //move interruptvectors to the Boot sector    
+	MCUCR = (1<<IVSEL);  // device specific !
 	
 	BLDDR  &= ~(1<<BLPNUM);	// set as Input
 	BLPORT |= (1<<BLPNUM);		// Enable pullup
@@ -155,8 +160,8 @@ int main(void)
 		{  
 			// jump to main app if pin is not grounded
 			BLPORT &= ~(1<<BLPNUM);  // set to default
-			MCUCR = (1<<IVCE); 
+			MCUCR = (1<<IVCE);       // move interruptvectors to the Application sector
-			MCUCR = (0<<IVSEL);      // move interruptvectors to the Application sector
+			MCUCR = (0<<IVSEL);      // device specific !
 			jump_to_app();	// Jump to application sector
 		}
 		else
@@ -179,6 +184,7 @@ int main(void)
 	}
 	
 	#elif defined(START_SIMPLE)
+	
 	if((BLPIN & (1<<BLPNUM)))
 	{  
 			  // jump to main app if pin is not grounded
@@ -188,6 +194,53 @@ int main(void)
 		jump_to_app();	// Jump to application sector
 	}
 
+
+	#elif defined(START_WAIT)
+	
+	// Timer-Setup for ATmega8 
+	// - verify that the configuration is valid for the target AVR
+	
+	#define F_OSC XTAL
+	#define UART0_STATUS UCSRA 
+	#define UART0_DATA UDR
+	#define MY_WAIT 900
+	// wait ca 1 sec (900ms)
+	TCCR1A = 0; // timer setup
+	// F_OSC / 8 / 1000 -> 1ms
+	#if (((F_OSC / 8 / 1000)*MY_WAIT) < 65535)
+		#warning Information: setting prescaler to 8
+		#define WAIT_VALUE ((F_OSC / 8 / 1000)*MY_WAIT)
+		TCCR1B |= _BV(CS01); 
+	#elif ((((F_OSC / 64 / 1000)*MY_WAIT) < 65535))
+		#warning Information: setting prescaler to 64
+		#define WAIT_VALUE ((F_OSC / 64 / 1000)*MY_WAIT)
+		TCCR1B |= _BV(CS01)| _BV(CS00); 
+	#elif ((((F_OSC / 256 / 1000)*MY_WAIT) < 65535))
+		#warning Information: setting prescaler to 256
+		#define WAIT_VALUE ((F_OSC / 256 / 1000)*MY_WAIT)
+		TCCR1B |= _BV(CS02); 
+	#else //((((F_OSC / 1024 / 1000)*MY_WAIT) < 65535))
+		#warning Information: setting prescaler to 1024
+		#define WAIT_VALUE ((F_OSC / 1024 / 1000)*MY_WAIT)
+		TCCR1B |= _BV(CS00) |_BV(CS02); //1024 prescaler
+	#endif
+	
+	while(1){
+		if(UART0_STATUS & (1<<RXC)){
+			if (UART0_DATA == 'S')
+				break;
+		}
+		if (TCNT1 >= WAIT_VALUE){
+			BLPORT &= ~(1<<BLPNUM);  // set to default
+			MCUCR = (1<<IVCE); 
+			MCUCR = (0<<IVSEL);             //move interruptvectors to the Application sector
+			TCCR1B = 0; // timer off
+			jump_to_app();	// Jump to application sector
+		}
+	}
+	TCCR1B = 0; // timer off
+	send_boot();
+	
 	#elif defined(START_BOOTICE)
 	#warning "BOOTICE mode - no startup-condition"
 

makefile

@@ -35,13 +35,14 @@
 
 # MCU name
 ## MCU = atmega16
-## MCU = atmega8
+MCU = atmega8
 ## MCU = atmega32
-MCU = at90can128
+## MCU = at90can128
 
 XTAL=16000000
-
+#XTAL=2000000UL
-BAUDRATE=115200
+#BAUDRATE=115200
+BAUDRATE=9600UL
 
 #Pin "STARTPIN" on port "STARTPORT" in this port has to grounded 
 #   (active low) to start the bootloader
@@ -63,7 +64,11 @@ BLPNUM = PINB0
 #     parser-loop on reset 
 #     XTAL in BOOTICEMODE must be 7372800 Hz to be compatible
 #     with the org. JTAGICE-Firmware */
-STARTMODE=START_SIMPLE
+#   * WAIT-mode waits 1 sec for the S command if nothing is recived
+#	  then the user prog is started ..
+
+#STARTMODE=START_SIMPLE
+STARTMODE=START_WAIT
 ##STARTMODE=START_POWERSAVE
 ##STARTMODE=START_BOOTICE
 
@@ -71,6 +76,7 @@ STARTMODE=START_SIMPLE
 ## NO! BOOTSIZE=_B128
 ## NO! BOOTSIZE=_B256  
 ## MAYBE: BOOTSIZE=_B512 
+#BOOTSIZE=_B512 
 BOOTSIZE=_B1024 
 ##BOOTSIZE=_B2048
 
@@ -109,7 +115,8 @@ endif
 
 
 # Output format. (can be srec, ihex, binary)
-FORMAT = srec
+FORMAT = ihex
+#FORMAT = srec
 
 # Target file name (without extension).
 TARGET = main
@@ -250,7 +257,7 @@ AVRDUDE_PROGRAMMER = stk500v2
 
 # com1 = serial port. Use lpt1 to connect to parallel port.
 #AVRDUDE_PORT = com1    # programmer connected to serial device
-AVRDUDE_PORT = /dev/ttyS1    # programmer connected to serial device
+AVRDUDE_PORT = /dev/ttyS0    # programmer connected to serial device
 
 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
@@ -280,25 +287,35 @@ AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 # ---------------------------------------------------------------------------
 
 # Define directories, if needed.
-DIRAVR = c:/winavr
+#DIRAVR = c:/winavr
-DIRAVRBIN = $(DIRAVR)/bin
+#DIRAVRBIN = $(DIRAVR)/bin
-DIRAVRUTILS = $(DIRAVR)/utils/bin
+#DIRAVRUTILS = $(DIRAVR)/utils/bin
-DIRINC = .
+#DIRINC = .
-DIRLIB = $(DIRAVR)/avr/lib
+#DIRLIB = $(DIRAVR)/avr/lib
 
 
+# Define programs and commands.
+#SHELL = $(DIRAVRUTILS)/sh
+#NM = $(DIRAVRBIN)/avr-nm 
+#CC = $(DIRAVRBIN)/avr-gcc
+#OBJCOPY = $(DIRAVRBIN)/avr-objcopy
+#OBJDUMP= $(DIRAVRBIN)/avr-objdump
+#SIZE = $(DIRAVRBIN)/avr-size
+#AVRDUDE = $(DIRAVRBIN)/avrdude.sh
+#REMOVE = rm -f
+#COPY = cp
+
 # Define programs and commands.
 SHELL = sh
-CC = env WINEDLLOVERRIDES=msvcrt=n /spare/bon/wine/wine/wine c:/WinAVR/bin/avr-gcc
+CC = avr-gcc
-OBJCOPY = env WINEDLLOVERRIDES=msvcrt=n /spare/bon/wine/wine/wine c:/WinAVR/bin/avr-objcopy
+OBJCOPY = avr-objcopy
-OBJDUMP = env WINEDLLOVERRIDES=msvcrt=n /spare/bon/wine/wine/wine c:/WinAVR/bin/avr-objdump
+OBJDUMP = avr-objdump
-SIZE = env WINEDLLOVERRIDES=msvcrt=n /spare/bon/wine/wine/wine c:/WinAVR/bin/avr-size
+SIZE = avr-size
-NM = env WINEDLLOVERRIDES=msvcrt=n /spare/bon/wine/wine/wine c:/WinAVR/bin/avr-nm
+NM = avr-nm
 AVRDUDE = avrdude
 REMOVE = rm -f
 COPY = cp
-
+WINSHELL = cmd
-
 
 
 # Define Messages

readme.txt

@@ -10,9 +10,28 @@
 
   http://www.siwawi.arubi.uni-kl.de/avr_projects
 
+  Addtional code and improvements provided by
+  Uwe Bonnes and Bjoern Riemer.
+
+
 ======================================================
 
 
+Programming-Software (on the "PC-Side"):
+
+* AVRProg (included in AVRStudio) available at www.atmel.com.
+  MS-Windows only. AVRProg can be used as stand-alone application.
+  (avrprog.exe)
+
+* avrdude available at http://savannah.nongnu.org/projects/avrdude/
+  "Multiplattform"
+
+
+
+09. Feb. 2006 - Version 0.75
+
+* additional STARTUP_WAIT support contributed by Bjoern Riemer
+
 18. Aug. 2005 - Version 0.74
 
 * AT90CAN128 support contributed by Uwe Bonnes
@@ -144,7 +163,8 @@ not enabled (TODO).
   or hold the key down until you see the AVRPROG dialog!
 
 - Start AVRPROG (AVRStuido/Tools or stand-alone) - 
-  keep PA7 grounded!
+  keep PA7 grounded! (avrdude is supported too, check
+  the avrdude manual for command-line options).
 
 - AVRPROG will detect the bootloader, you may release
   PA7 now