2019-11-06 10:03:47 +01:00
|
|
|
# twiboot - a TWI / I2C bootloader for AVR MCUs ##
|
|
|
|
|
twiboot is a simple/small bootloader for AVR MCUs with integrated TWI peripheral written in C.
|
|
|
|
|
It was originally created to update I2C controlled BLMCs (Brushless Motor Controller) without an AVR ISP adapter.
|
|
|
|
|
|
|
|
|
|
twiboot acts as a slave device on a TWI/I2C bus and allows reading/writing of the internal flash memory.
|
|
|
|
|
As a compile time option twiboot also allows reading/writing of the whole internal EEPROM memory.
|
|
|
|
|
The bootloader is not able to update itself (only application flash memory region accessible).
|
|
|
|
|
|
|
|
|
|
Currently the following AVR MCUs are supported:
|
|
|
|
|
|
|
|
|
|
AVR MCU | Flash bytes used (.text + .data) | Bootloader region size
|
|
|
|
|
--- | --- | ---
|
2019-11-03 08:58:02 +01:00
|
|
|
atmega8 | 868 (0x364) | 512 words
|
|
|
|
|
atmega88 | 920 (0x398) | 512 words
|
|
|
|
|
atmega168 | 972 (0x3CC) | 512 words
|
|
|
|
|
atmega328p | 972 (0x3CC) | 512 words
|
2019-11-06 10:03:47 +01:00
|
|
|
(Compiled on Ubuntu 18.04 LTS (gcc 5.4.0 / avr-libc 2.0.0) with EEPROM and LED support)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## Operation ##
|
|
|
|
|
twiboot is installed in the bootloader memory region and executed directly after reset (BOOTRST fuse is programmed).
|
|
|
|
|
|
|
|
|
|
While running, twiboot configures the TWI peripheral as slave device and waits for valid protocol messages
|
|
|
|
|
directed to its address on the TWI/I2C bus. The slave address is configured during compile time of twiboot.
|
|
|
|
|
When receiving no messages for 1000ms after reset, the bootloader exits and executes the main application at address 0x0000.
|
|
|
|
|
|
|
|
|
|
A TWI/I2C master can use the protocol to
|
|
|
|
|
- abort the boot timeout
|
|
|
|
|
- query information about the device (bootloader version, AVR signature bytes, flash/eeprom size, flash page size)
|
|
|
|
|
- read internal flash / eeprom memory (byte wise)
|
|
|
|
|
- write the internal flash (page wise)
|
|
|
|
|
- write the internal eeprom (byte wise)
|
|
|
|
|
- exit the bootloader and start the application
|
|
|
|
|
|
|
|
|
|
As a compile time option twiboot can output its state with two LEDs.
|
|
|
|
|
One LED will flash with a frequency of 20Hz while twiboot is active (including boot wait time).
|
|
|
|
|
A second LED will flash when the bootloader is addressed on the TWI/I2C bus.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## Build and install twiboot ##
|
|
|
|
|
twiboot uses gcc, avr-libc and GNU Make for building, avrdude is used for flashing the MCU.
|
|
|
|
|
The build and install procedures are only tested under linux.
|
|
|
|
|
|
|
|
|
|
The selection of the target MCU and the programming interface can be found in the Makefile,
|
|
|
|
|
TWI/I2C slave address and optional components (EEPROM / LED support) are configured
|
|
|
|
|
in the main.c source.
|
|
|
|
|
|
|
|
|
|
To build twiboot for the selected target:
|
|
|
|
|
``` shell
|
|
|
|
|
$ make
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
To install (flash download) twiboot with avrdude on the target:
|
|
|
|
|
``` shell
|
|
|
|
|
$ make install
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
Set AVR fuses with avrdude on the target (internal RC-Osz, enable BOD, enable BOOTRST):
|
|
|
|
|
``` shell
|
|
|
|
|
$ make fuses
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## TWI/I2C Protocol ##
|
|
|
|
|
A TWI/I2C master can use the following protocol for accessing the bootloader.
|
|
|
|
|
|
|
|
|
|
Function | TWI/I2C data | Comment
|
|
|
|
|
--- | --- | ---
|
|
|
|
|
Abort boot timeout | **SLA+W**, 0x00, **STO** |
|
|
|
|
|
Show bootloader version | **SLA+W**, 0x01, **SLA+R**, {16 bytes}, **STO** | ASCII, not null terminated
|
|
|
|
|
Start application | **SLA+W**, 0x01, 0x80, **STO** |
|
|
|
|
|
Read chip info | **SLA+W**, 0x02, 0x00, 0x00, 0x00, **SLA+R**, {8 bytes}, **STO** | 3byte signature, 1byte page size, 2byte flash size, 2byte eeprom size
|
|
|
|
|
Read 1+ flash bytes | **SLA+W**, 0x02, 0x01, addrh, addrl, **SLA+R**, {* bytes}, **STO** |
|
|
|
|
|
Read 1+ eeprom bytes | **SLA+W**, 0x02, 0x02, addrh, addrl, **SLA+R**, {* bytes}, **STO** |
|
|
|
|
|
Write one flash page | **SLA+W**, 0x02, 0x01, addrh, addrl, {* bytes}, **STO** | page size as indicated in chip info
|
|
|
|
|
Write 1+ eeprom bytes | **SLA+W**, 0x02, 0x02, addrh, addrl, {* bytes}, **STO** |
|
|
|
|
|
|
|
|
|
|
**SLA+R** means Start Condition, Slave Address, Read Access
|
|
|
|
|
|
|
|
|
|
**SLA+W** means Start Condition, Slave Address, Write Access
|
|
|
|
|
|
|
|
|
|
**STO** means Stop Condition
|
|
|
|
|
|
|
|
|
|
The multiboot_tool repository contains a simple linux application that uses
|
|
|
|
|
this protocol to access the bootloader over linux i2c device.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## Development ##
|
|
|
|
|
Issue reports, feature requests, patches or simply success stories are much appreciated.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## Roadmap ##
|
|
|
|
|
Some ideas that I want to investigate / implement in twiboot:
|
|
|
|
|
- [ ] do not use interrupts and remove vector table to save flash space
|
|
|
|
|
- [ ] find a way to not rely on TWI clock stretching during write access
|
|
|
|
|
- [ ] support AVR TINYs (USI peripheral, no bootloader fuse, no Read-While-Write flash)
|
