A TWI / I2C bootloader for AVR MCUs
Go to file
Olaf Rempel c5f5a74783 Increment major version
Make a major version bump since the clockstretching changes require
retries/polling and might break current master implementations.
2020-02-02 00:08:13 +01:00
.gitignore update Makefile 2014-10-05 14:32:07 +02:00
LICENSE Update code style 2019-11-06 13:18:53 +01:00
Makefile Do not use IRQs and remove vector table 2019-11-06 13:18:53 +01:00
README.md Do not rely on Clockstretching for writes 2020-02-02 00:03:09 +01:00
main.c Increment major version 2020-02-02 00:08:13 +01:00

README.md

twiboot - a TWI / I2C bootloader for AVR MCUs

twiboot is a simple/small bootloader for AVR MCUs with integrated TWI peripheral written in C. It was originally created to update I2C controlled BLMCs (Brushless Motor Controller) without an AVR ISP adapter.

twiboot acts as a slave device on a TWI/I2C bus and allows reading/writing of the internal flash memory. As a compile time option (EEPROM_SUPPORT) twiboot also allows reading/writing of the whole internal EEPROM memory. The bootloader is not able to update itself (only application flash memory region accessible).

Currently the following AVR MCUs are supported:

AVR MCU Flash bytes used (.text + .data) Bootloader region size
atmega8 802 (0x322) 512 words
atmega88 826 (0x33A) 512 words
atmega168 826 (0x33A) 512 words
atmega328p 826 (0x33A) 512 words

(Compiled on Ubuntu 18.04 LTS (gcc 5.4.0 / avr-libc 2.0.0) with EEPROM and LED support)

Operation

twiboot is installed in the bootloader memory region and executed directly after reset (BOOTRST fuse is programmed).

While running, twiboot configures the TWI peripheral as slave device and waits for valid protocol messages directed to its address on the TWI/I2C bus. The slave address is configured during compile time of twiboot. When receiving no messages for 1000ms after reset, the bootloader exits and executes the main application at address 0x0000.

A TWI/I2C master can use the protocol to

  • abort the boot timeout
  • query information about the device (bootloader version, AVR signature bytes, flash/eeprom size, flash page size)
  • read internal flash / eeprom memory (byte wise)
  • write the internal flash (page wise)
  • write the internal eeprom (byte wise)
  • exit the bootloader and start the application

As a compile time option (LED_SUPPORT) twiboot can output its state with two LEDs. One LED will flash with a frequency of 20Hz while twiboot is active (including boot wait time). A second LED will flash when the bootloader is addressed on the TWI/I2C bus.

Build and install twiboot

twiboot uses gcc, avr-libc and GNU Make for building, avrdude is used for flashing the MCU. The build and install procedures are only tested under linux.

The selection of the target MCU and the programming interface can be found in the Makefile, TWI/I2C slave address and optional components (EEPROM / LED support) are configured in the main.c source.

To build twiboot for the selected target:

$ make

To install (flash download) twiboot with avrdude on the target:

$ make install

Set AVR fuses with avrdude on the target (internal RC-Osz, enable BOD, enable BOOTRST):

$ make fuses

TWI/I2C Protocol

A TWI/I2C master can use the following protocol for accessing the bootloader.

Function TWI/I2C data Comment
Abort boot timeout SLA+W, 0x00, STO
Show bootloader version SLA+W, 0x01, SLA+R, {16 bytes}, STO ASCII, not null terminated
Start application SLA+W, 0x01, 0x80, STO
Read chip info SLA+W, 0x02, 0x00, 0x00, 0x00, SLA+R, {8 bytes}, STO 3byte signature, 1byte page size, 2byte flash size, 2byte eeprom size
Read 1+ flash bytes SLA+W, 0x02, 0x01, addrh, addrl, SLA+R, {* bytes}, STO
Read 1+ eeprom bytes SLA+W, 0x02, 0x02, addrh, addrl, SLA+R, {* bytes}, STO
Write one flash page SLA+W, 0x02, 0x01, addrh, addrl, {* bytes}, STO page size as indicated in chip info
Write 1+ eeprom bytes SLA+W, 0x02, 0x02, addrh, addrl, {* bytes}, STO write 0 < n < page size bytes at once

SLA+R means Start Condition, Slave Address, Read Access

SLA+W means Start Condition, Slave Address, Write Access

STO means Stop Condition

A flash page / eeprom write is only triggered after the Stop Condition. During the write process twiboot will NOT acknowledge its slave address.

The multiboot_tool repository contains a simple linux application that uses this protocol to access the bootloader over linux i2c device.

The ispprog programming adapter can also be used as a avr910/butterfly to twiboot protocol bridge.

TWI/I2C Clockstretching

While a write is in progress twiboot will not respond on the TWI/I2C bus and the TWI/I2C master needs to retry/poll the slave address until the write has completed.

As a compile time option (USE_CLOCKSTRETCH) the previous behavior of twiboot can be restored: TWI/I2C Clockstretching is then used to inform the master of the duration of the write. Please note that there are some TWI/I2C masters that do not support clockstretching.

Development

Issue reports, feature requests, patches or simply success stories are much appreciated.

Roadmap

Some ideas that I want to investigate / implement in twiboot:

  • support AVR TINYs (USI peripheral, no bootloader fuse, no Read-While-Write flash)