313 lines
9.2 KiB
C
313 lines
9.2 KiB
C
|
/*
|
||
|
|
* (C) Copyright 2001-2005
|
||
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
||
|
|
*
|
||
|
|
* See file CREDITS for list of people who contributed to this
|
||
|
|
* project.
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or
|
||
|
|
* modify it under the terms of the GNU General Public License as
|
||
|
|
* published by the Free Software Foundation; either version 2 of
|
||
|
|
* the License, or (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program; if not, write to the Free Software
|
||
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
||
|
|
* MA 02111-1307 USA
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
*
|
||
|
|
* Configuration settings for the CU824 board.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* ------------------------------------------------------------------------- */
|
||
|
|
|
||
|
|
/*
|
||
|
|
* board/config.h - configuration options, board specific
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef __CONFIG_H
|
||
|
|
#define __CONFIG_H
|
||
|
|
|
||
|
|
/*
|
||
|
|
* High Level Configuration Options
|
||
|
|
* (easy to change)
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define CONFIG_MPC824X 1
|
||
|
|
#define CONFIG_MPC8240 1
|
||
|
|
#define CONFIG_CU824 1
|
||
|
|
|
||
|
|
|
||
|
|
#define CONFIG_CONS_INDEX 1
|
||
|
|
#define CONFIG_BAUDRATE 9600
|
||
|
|
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
||
|
|
|
||
|
|
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
|
||
|
|
|
||
|
|
#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
|
||
|
|
#define CONFIG_BOOTDELAY 5
|
||
|
|
|
||
|
|
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
|
||
|
|
|
||
|
|
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
|
||
|
|
|
||
|
|
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
|
||
|
|
CFG_CMD_BEDBUG | \
|
||
|
|
0 /* CFG_CMD_DATE */ | \
|
||
|
|
CFG_CMD_DHCP | \
|
||
|
|
CFG_CMD_PCI | \
|
||
|
|
CFG_CMD_NFS | \
|
||
|
|
CFG_CMD_SNTP )
|
||
|
|
|
||
|
|
/* This must be included AFTER the definition of CONFIG_COMMANDS (if any)
|
||
|
|
*/
|
||
|
|
#include <cmd_confdefs.h>
|
||
|
|
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Miscellaneous configurable options
|
||
|
|
*/
|
||
|
|
#define CFG_LONGHELP /* undef to save memory */
|
||
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
||
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
||
|
|
|
||
|
|
#if 1
|
||
|
|
#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
|
||
|
|
#endif
|
||
|
|
#ifdef CFG_HUSH_PARSER
|
||
|
|
#define CFG_PROMPT_HUSH_PS2 "> "
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/* Print Buffer Size
|
||
|
|
*/
|
||
|
|
#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
|
||
|
|
|
||
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
||
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
||
|
|
#define CFG_LOAD_ADDR 0x00100000 /* Default load address */
|
||
|
|
|
||
|
|
/*-----------------------------------------------------------------------
|
||
|
|
* Start addresses for the final memory configuration
|
||
|
|
* (Set up by the startup code)
|
||
|
|
* Please note that CFG_SDRAM_BASE _must_ start at 0
|
||
|
|
*/
|
||
|
|
#define CFG_SDRAM_BASE 0x00000000
|
||
|
|
#define CFG_FLASH_BASE 0xFF000000
|
||
|
|
|
||
|
|
#define CFG_RESET_ADDRESS 0xFFF00100
|
||
|
|
|
||
|
|
#define CFG_EUMB_ADDR 0xFCE00000
|
||
|
|
|
||
|
|
#define CFG_MONITOR_BASE TEXT_BASE
|
||
|
|
|
||
|
|
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
||
|
|
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
||
|
|
|
||
|
|
#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
|
||
|
|
#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
|
||
|
|
|
||
|
|
/* Maximum amount of RAM.
|
||
|
|
*/
|
||
|
|
#define CFG_MAX_RAM_SIZE 0x10000000
|
||
|
|
|
||
|
|
|
||
|
|
#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
|
||
|
|
#undef CFG_RAMBOOT
|
||
|
|
#else
|
||
|
|
#define CFG_RAMBOOT
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
/*-----------------------------------------------------------------------
|
||
|
|
* Definitions for initial stack pointer and data area
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Size in bytes reserved for initial data
|
||
|
|
*/
|
||
|
|
#define CFG_GBL_DATA_SIZE 128
|
||
|
|
|
||
|
|
#define CFG_INIT_RAM_ADDR 0x40000000
|
||
|
|
#define CFG_INIT_RAM_END 0x1000
|
||
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
||
|
|
|
||
|
|
/*
|
||
|
|
* NS16550 Configuration
|
||
|
|
*/
|
||
|
|
#define CFG_NS16550
|
||
|
|
#define CFG_NS16550_SERIAL
|
||
|
|
|
||
|
|
#define CFG_NS16550_REG_SIZE 4
|
||
|
|
|
||
|
|
#define CFG_NS16550_CLK (14745600 / 2)
|
||
|
|
|
||
|
|
#define CFG_NS16550_COM1 0xFE800080
|
||
|
|
#define CFG_NS16550_COM2 0xFE8000C0
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Low Level Configuration Settings
|
||
|
|
* (address mappings, register initial values, etc.)
|
||
|
|
* You should know what you are doing if you make changes here.
|
||
|
|
* For the detail description refer to the MPC8240 user's manual.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define CONFIG_SYS_CLK_FREQ 33000000
|
||
|
|
#define CFG_HZ 1000
|
||
|
|
|
||
|
|
/* Bit-field values for MCCR1.
|
||
|
|
*/
|
||
|
|
#define CFG_ROMNAL 0
|
||
|
|
#define CFG_ROMFAL 7
|
||
|
|
|
||
|
|
/* Bit-field values for MCCR2.
|
||
|
|
*/
|
||
|
|
#define CFG_REFINT 430 /* Refresh interval */
|
||
|
|
|
||
|
|
/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
|
||
|
|
*/
|
||
|
|
#define CFG_BSTOPRE 192
|
||
|
|
|
||
|
|
/* Bit-field values for MCCR3.
|
||
|
|
*/
|
||
|
|
#define CFG_REFREC 2 /* Refresh to activate interval */
|
||
|
|
#define CFG_RDLAT 3 /* Data latancy from read command */
|
||
|
|
|
||
|
|
/* Bit-field values for MCCR4.
|
||
|
|
*/
|
||
|
|
#define CFG_PRETOACT 2 /* Precharge to activate interval */
|
||
|
|
#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */
|
||
|
|
#define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */
|
||
|
|
#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */
|
||
|
|
#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length */
|
||
|
|
#define CFG_ACTORW 2
|
||
|
|
#define CFG_REGISTERD_TYPE_BUFFER 1
|
||
|
|
|
||
|
|
/* Memory bank settings.
|
||
|
|
* Only bits 20-29 are actually used from these vales to set the
|
||
|
|
* start/end addresses. The upper two bits will always be 0, and the lower
|
||
|
|
* 20 bits will be 0x00000 for a start address, or 0xfffff for an end
|
||
|
|
* address. Refer to the MPC8240 book.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define CFG_BANK0_START 0x00000000
|
||
|
|
#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1)
|
||
|
|
#define CFG_BANK0_ENABLE 1
|
||
|
|
#define CFG_BANK1_START 0x3ff00000
|
||
|
|
#define CFG_BANK1_END 0x3fffffff
|
||
|
|
#define CFG_BANK1_ENABLE 0
|
||
|
|
#define CFG_BANK2_START 0x3ff00000
|
||
|
|
#define CFG_BANK2_END 0x3fffffff
|
||
|
|
#define CFG_BANK2_ENABLE 0
|
||
|
|
#define CFG_BANK3_START 0x3ff00000
|
||
|
|
#define CFG_BANK3_END 0x3fffffff
|
||
|
|
#define CFG_BANK3_ENABLE 0
|
||
|
|
#define CFG_BANK4_START 0x3ff00000
|
||
|
|
#define CFG_BANK4_END 0x3fffffff
|
||
|
|
#define CFG_BANK4_ENABLE 0
|
||
|
|
#define CFG_BANK5_START 0x3ff00000
|
||
|
|
#define CFG_BANK5_END 0x3fffffff
|
||
|
|
#define CFG_BANK5_ENABLE 0
|
||
|
|
#define CFG_BANK6_START 0x3ff00000
|
||
|
|
#define CFG_BANK6_END 0x3fffffff
|
||
|
|
#define CFG_BANK6_ENABLE 0
|
||
|
|
#define CFG_BANK7_START 0x3ff00000
|
||
|
|
#define CFG_BANK7_END 0x3fffffff
|
||
|
|
#define CFG_BANK7_ENABLE 0
|
||
|
|
|
||
|
|
#define CFG_ODCR 0xff
|
||
|
|
|
||
|
|
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
|
||
|
|
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
||
|
|
|
||
|
|
#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
|
||
|
|
#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
|
||
|
|
|
||
|
|
#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
|
||
|
|
#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
|
||
|
|
|
||
|
|
#define CFG_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
|
||
|
|
#define CFG_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP)
|
||
|
|
|
||
|
|
#define CFG_DBAT0L CFG_IBAT0L
|
||
|
|
#define CFG_DBAT0U CFG_IBAT0U
|
||
|
|
#define CFG_DBAT1L CFG_IBAT1L
|
||
|
|
#define CFG_DBAT1U CFG_IBAT1U
|
||
|
|
#define CFG_DBAT2L CFG_IBAT2L
|
||
|
|
#define CFG_DBAT2U CFG_IBAT2U
|
||
|
|
#define CFG_DBAT3L CFG_IBAT3L
|
||
|
|
#define CFG_DBAT3U CFG_IBAT3U
|
||
|
|
|
||
|
|
/*
|
||
|
|
* For booting Linux, the board info and command line data
|
||
|
|
* have to be in the first 8 MB of memory, since this is
|
||
|
|
* the maximum mapped by the Linux kernel during initialization.
|
||
|
|
*/
|
||
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
||
|
|
|
||
|
|
/*-----------------------------------------------------------------------
|
||
|
|
* FLASH organization
|
||
|
|
*/
|
||
|
|
#define CFG_MAX_FLASH_BANKS 2 /* Max number of flash banks */
|
||
|
|
#define CFG_MAX_FLASH_SECT 39 /* Max number of sectors in one bank */
|
||
|
|
|
||
|
|
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
||
|
|
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
||
|
|
|
||
|
|
/* Warining: environment is not EMBEDDED in the U-Boot code.
|
||
|
|
* It's stored in flash separately.
|
||
|
|
*/
|
||
|
|
#define CFG_ENV_IS_IN_FLASH 1
|
||
|
|
#if 0
|
||
|
|
#define CFG_ENV_ADDR 0xFF008000
|
||
|
|
#define CFG_ENV_SIZE 0x8000 /* Size of the Environment Sector */
|
||
|
|
#else
|
||
|
|
#define CFG_ENV_ADDR 0xFFFC0000
|
||
|
|
#define CFG_ENV_SIZE 0x4000 /* Size of the Environment */
|
||
|
|
#define CFG_ENV_OFFSET 0 /* starting right at the beginning */
|
||
|
|
#define CFG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*-----------------------------------------------------------------------
|
||
|
|
* Cache Configuration
|
||
|
|
*/
|
||
|
|
#define CFG_CACHELINE_SIZE 32
|
||
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
||
|
|
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Internal Definitions
|
||
|
|
*
|
||
|
|
* Boot Flags
|
||
|
|
*/
|
||
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
||
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
||
|
|
|
||
|
|
/*-----------------------------------------------------------------------
|
||
|
|
* PCI stuff
|
||
|
|
*-----------------------------------------------------------------------
|
||
|
|
*/
|
||
|
|
#define CONFIG_PCI /* include pci support */
|
||
|
|
#undef CONFIG_PCI_PNP
|
||
|
|
|
||
|
|
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
|
||
|
|
|
||
|
|
#define CONFIG_TULIP
|
||
|
|
#define CONFIG_TULIP_USE_IO
|
||
|
|
|
||
|
|
#define CFG_ETH_DEV_FN 0x7800
|
||
|
|
#define CFG_ETH_IOBASE 0x00104000
|
||
|
|
|
||
|
|
#define CONFIG_EEPRO100
|
||
|
|
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
|
||
|
|
#define PCI_ENET0_IOADDR 0x00104000
|
||
|
|
#define PCI_ENET0_MEMADDR 0x80000000
|
||
|
|
#endif /* __CONFIG_H */
|